Programming HomeLink® (for U.S. owners)

The HomeLink® compatible transceiver in your vehicle has 3 buttons which can be programmed to operate 3 different devices. Refer to the programming method below appropriate for the device.

1. Indicator light

1. Indicator light

2. Buttons

 - Programming HomeLink®

Point the remote control transmit- ter for the device 1 in. (25 mm) from the HomeLink® buttons.

Keep the HomeLink® indicator light in view while programming.

Press and hold one of the HomeLink® buttons and the trans- mitter button. When

Press and hold one of the HomeLink® buttons and the trans- mitter button. When the HomeLink® indicator light changes from a slow to a rapid flash, you can release both buttons.

If the HomeLink® indicator light comes on but does not flash, or flashes rapidly for 2 seconds and remains lit, the HomeLink® button is already programmed. Use the other buttons or follow the “Repro- gramming a HomeLink® button” instructions.

Test the HomeLink® operation by pressing the newly programmed button.

Test the HomeLink® operation by pressing the newly programmed button.

If a HomeLink® button has been programmed for a garage door, check to see if the garage door opens and closes. If the garage door does not operate, see if your garage transmitter is of the rolling code type. Press and hold the pro- grammed HomeLink® button. The remote control transmitter is of the rolling code type if the HomeLink® indicator light flashes rapidly for 2 seconds and then remains lit. If your transmitter is the rolling code type, proceed to the heading “Pro- gramming a rolling code system”.

Repeat the steps above to program

another device for any of the remaining HomeLink® buttons. Repeat the steps above to program another device for any of the remaining HomeLink® buttons.

 - Programming a rolling code system (for U.S. owners)

If your device is rolling code equipped, follow the steps under the heading “Programming HomeLink®” before proceeding with the steps listed below.

mounted garage door opener motor. The exact location and color of the button mayLocate the learn button on the ceiling mounted garage door opener motor. The exact location and color of the button may vary by brand of garage door opener.

Refer to the operation manual supplied with the garage door opener for the location of the learn button.

Following this step, you have 30 seconds in which to initiate step 3 below. Press the learn button.

Following this step, you have 30 seconds in which to initiate step 3 below.

programmed HomeLink® button for 2 seconds and release it. Repeat this step once Press and release the vehicle’s programmed HomeLink® button for 2 seconds and release it. Repeat this step once again. The garage door may open.

If the garage door opens, the programming process is complete. If the door does not open, press and release the button a third time. This third press and release will complete the programming process by opening the garage door.

The ceiling mounted garage door opener motor should now recognize the HomeLink® signal and operate the garage door.

another rolling code system for any of the remaining HomeLink® buttons. Repeat the steps above to program another rolling code system for any of the remaining HomeLink® buttons.

 - Programming an entry gate (for U.S. owners)/Programming a device in the Canadian market

1 in. (25 mm) away from the HomeLink® buttons. Place the remote control transmitter 1 in. (25 mm) away from the HomeLink® buttons.

Keep the HomeLink® indicator light in view while programming.

button. Press and hold the selected HomeLink® button.

the remote control trans- mitter for 2 seconds each until step 4 is completed.Repeatedly press and release (cycle) the remote control trans- mitter for 2 seconds each until step 4 is completed.

starts to flash rapidly, release the buttons. When the HomeLink® indicator light starts to flash rapidly, release the buttons.

pressing the newly pro- grammed button. Check to see if the gate/device operates Test the HomeLink® operation by pressing the newly pro- grammed button. Check to see if the gate/device operates cor- rectly.

another device for each of the remaining HomeLink® buttons. Repeat the steps above to program another device for each of the remaining HomeLink® buttons.

 - Programming other devices

To program other devices such as home security systems, home door locks or lighting, contact your Lexus dealer for assistance.

 - Reprogramming a button

The individual HomeLink® buttons cannot be erased but can be reprogrammed. To reprogram a button, follow the “Reprogramming a HomeLink® button” instructions.

    See also:

    What is not covered
    These warranty obligations do not apply to failures or noncompliance caused by:  • The use of replacement parts not certified in accordance with aftermarket parts certification regulation ...

    How do I request arbitration?
    To initiate arbitration, you must complete an NCDS customer claim form and mail it to NCDS. A claim form is included in the Lemon Law Guide located in your vehicle, or you may request a form by ca ...

    Hands-free System (For Cellular Phone)
    ■Bluetooth® phone pairing Compatible Bluetooth®-equipped phones can be connected to the vehicle, enabling hands-free operation. Please refer to the cellular phone manufacturer’s user g ...